Kenmore Pro 72583 Manuel du propriétaire télécharger pdf (Page 41)

Before You Call

Surface burners do not ignite. • Surface control knob was not completely turned to LITE. Push in and turn the surface

control knob to LITE until burner ignites and then turn control knob to desired flame size.

• Burner ports are clogged. With the burner OFF, use a small-gauge wire or needle to

burner head slots and ignition ports. See “Cleaning Surface Burner Heads” on page 36.

• Range power cord is disconnected from outlet (electric ignition models only). Be sure

power cord is securely plugged into the power outlet.

• Electrical power outage. Burners may be lit manually. See “Setting the Turbo Boil, Simmer,

Power, and Standard Surface Burners” on page 12.

• Be sure the gas supply to the range is turned on.

Surface burner flame uneven or only

part way around burner cap.

• Burner slots or ports are clogged. With the surface burner OFF, clean ports with a small-

gauge wire or needle. Also, moisture is present after cleaning. Lightly fan the flame and

allow burner to operate until flame is full.

• Burner caps are not seated properly. Check that all burner caps are level and seated

correctly on burner heads. See “Cleaning Surface Burner Heads” on page 36.

Surface burner flame is orange. • Dust particles in main gas line. Allow the burner to operate a few minutes until flame

turns blue. In coastal areas, a slightly orange flame is unavoidable due to salt content in

air.

• Incorrect L.P. conversion. Refer to L.P. conversion kit instructions to correct.

Oven smokes excessively when

broiling.

• Incorrect setting. Follow broiling instructions in the “Setting Broil” on page 22.

• Meat too close to the broil element. Reposition broil rack to provide proper clearance

between the meat and broil element. Remove excess fat from meat. Cut remaining fatty

edges to prevent curling.

• Grease build up on oven surfaces. Regular cleaning is necessary when broiling

frequently. Grease or food splatters will cause excessive smoking.

• Insert on broiler pan wrong side up. Grease does not drain into broiler pan. Always place

the insert on the broiler pan with the ribs up and the slots down to allow grease to drip

into the pan.

• Broiler pan used without insert or insert cover with aluminum foil. Do not use the broiler

pan without the insert or cover the insert with aluminum foil.

Convection fan does not rotate • Oven door is open. Convection fan will turn off if oven door is opened when convection is

active. Close oven door.

Oven control panel beeps and

displays an F code error.

• Oven control has detected a fault or error condition. Press STOP/CLEAR to clear the

error code. Try bake or broil function. If the F code error repeats, turn off power to appli-

ance, wait 5 minutes and then repower appliance. Set clock with correct time of day. Try

bake or broil function again. If fault recurs, press STOP to clear and call 1-844-553-6667

in the U.S.A. and 1-800-469-4663 in Canada for assistance (see back cover).

Soil not completely removed after

self clean.

•

Self Clean was interrupted. Review “Clean” on page 32.

• Excessive spills on oven bottom. Clean before starting self clean.

• Failure to clean soil from the oven frame, the door liner outside the oven door gasket, and

the small area at the front center of the oven bottom. These areas are not in the self-

cleaning area, but they get hot enough to burn on residue. Clean these areas before

starting the self-cleaning cycle. Burned-on residue can be cleaned with a stiff nylon brush

and water or a nylon scrubber. Be careful not to damage the oven gasket.

1 2 ... 36 37 38 39 40 41 42 43 44

Commentaires sur ces manuels

Pas de commentaire

Kenmore Pro 72583 Manuel du propriétaire Page 41

Commentaires sur ces manuels

Produits connexes et manuels pour Cuisiniers Kenmore Pro 72583